Difference between revisions of "Receivers:Vu"

From OpenPLi Wiki
Jump to: navigation, search
Line 57: Line 57:
 
# The flashing is done when the led light rapidly blinks on the front panel.
 
# The flashing is done when the led light rapidly blinks on the front panel.
 
# Switch the power off and on again to reboot.
 
# Switch the power off and on again to reboot.
 +
 +
 +
 +
'''How to flash Vu<sup>+</sup> Solo 2 receiver...'''<br />
 +
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.
 +
 +
# Format your USB stick with a FAT32 file system
 +
# Download the USB image of your choice on http://openpli.org/download/vuplus/vusolo2/
 +
# Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory vuplus and in this directory you find a directory solo2 in which you find the necessary files.
 +
# Insert the prepared USB stick into the front of your VU+ Solo2 receiver
 +
# Switch your VU+ Solo2 off (power-off, not stand-by!). Or choose restart in your receiver: Menu -> Standby / Restart -> Restart and go directly to step 7
 +
# Switch your VU+ Solo2 on
 +
# After powering on the Solo2 you see: Starting. If the USB-stick is properly recognised you will see the following text (alternating) Update! Press Power
 +
# During the showing of the above text press the power button (on the receiver!) The text will be shown about 5-8 seconds.
 +
# After the flash procedure the Solo2 will be rebooted automatically. If not switch the power off and on again to reboot.
 +
 +
Note: Please bear in mind: To flash an image there may be only one USB-device connected with the receiver and that's the USB-device with the image you want to flash. If there are more USB-devices connected the flash procedure will most likely fail and won't even start!

Revision as of 18:55, 12 June 2017

Supported receivers

RECEIVERS-Vu-001.jpg.png

Solo
Duo
Uno
Ultimo
Solo2
Duo2
Solo SE
Zero
Solo 4K
Uno 4K
Ultimo 4K


How to flash Vu+ Zero receiver...
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

  1. Format your USB stick with a FAT32 file system
  2. Download the USB image of your choice on http://openpli.org/download/vuplus/vuzero/
  3. Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory vuplus and in this directory you find a directory zero in which you find the necessary files.
  4. Disconnect all USB flash drives connected to your receiver.
  5. Insert the prepared USB stick into the back of your VU+ Zero receiver
  6. Switch your VU+ Zero off (power-off, not stand-by!). Or choose restart in your receiver: Menu -> Standby / Restart -> Restart and go directly to step 8
  7. Switch your VU+ Zero on
  8. The white led will quickly flash two or three times then start to fade in and out slowly.
  9. The flashing is done when the led light rapidly blinks on the front panel.
  10. Switch the power off and on again to reboot.


How to flash Vu+ Duo receiver...
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

  1. Format your USB stick with a FAT32 file system
  2. Download the USB image of your choice on http://openpli.org/download/vuplus/vuduo/
  3. Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory vuplus and in this directory you find a directory duo in which you find the necessary files.
  4. Insert the prepared USB stick into the front of your VU+ Duo receiver
  5. Switch your VU+ Duo off (power-off, not stand-by!). Or choose restart in your receiver: Menu -> Standby / Restart -> Restart and go directly to step 7
  6. Switch your VU+ Duo on
  7. Wait until you receive the message to reboot your Vu+ Duo
  8. Remove the USB-stick and switch the power off and on again to reboot.


How to flash Vu+ Solo SE receiver...
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

  1. Format your USB stick with a FAT32 file system
  2. Download the USB image of your choice on http://openpli.org/download/vuplus/vusolose/
  3. Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory vuplus and in this directory you find a directory zero in which you find the necessary files.
  4. Disconnect all USB flash drives connected to your receiver.
  5. Insert the prepared USB stick into the back of your VU+SoloSE receiver
  6. Switch your VU+SoloSE off (power-off, not stand-by!). Or choose restart in your receiver: Menu -> Standby / Restart -> Restart and go directly to step 8
  7. Switch your VU+SoloSE on
  8. The white led will quickly flash two or three times then start to fade in and out slowly.
  9. The flashing is done when the led light rapidly blinks on the front panel.
  10. Switch the power off and on again to reboot.


How to flash Vu+ Solo 2 receiver...
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

  1. Format your USB stick with a FAT32 file system
  2. Download the USB image of your choice on http://openpli.org/download/vuplus/vusolo2/
  3. Extract the USB image (it is a .zip archive) on your PC using your favorite unzip tool to the root directory of your USB stick. The result is that you get a directory vuplus and in this directory you find a directory solo2 in which you find the necessary files.
  4. Insert the prepared USB stick into the front of your VU+ Solo2 receiver
  5. Switch your VU+ Solo2 off (power-off, not stand-by!). Or choose restart in your receiver: Menu -> Standby / Restart -> Restart and go directly to step 7
  6. Switch your VU+ Solo2 on
  7. After powering on the Solo2 you see: Starting. If the USB-stick is properly recognised you will see the following text (alternating) Update! Press Power
  8. During the showing of the above text press the power button (on the receiver!) The text will be shown about 5-8 seconds.
  9. After the flash procedure the Solo2 will be rebooted automatically. If not switch the power off and on again to reboot.

Note: Please bear in mind: To flash an image there may be only one USB-device connected with the receiver and that's the USB-device with the image you want to flash. If there are more USB-devices connected the flash procedure will most likely fail and won't even start!

Retrieved from "https://wiki.openpli.org/index.php?title=Receivers:Vu&oldid=3956"