Difference between revisions of "Receivers:Mut@nt"
Rick Hunter (talk | contribs) |
|||
| Line 25: | Line 25: | ||
<u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force" | <u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force" | ||
| + | |||
| + | ---- | ||
| + | Specific information for HD51 | ||
| + | New bootloader V1.07-r19 for Mut@nt HD51 model. | ||
| + | |||
| + | The file can be download at: http://downloads.mut...olt-v107r19.zip | ||
| + | |||
| + | To check with boot loader version you have... Enter the receiver with telnet, enter the following command: | ||
| + | #:/cat /sys/firmware/devicetree/base/bolt/tag ( bolt versie nummer opvragen: v1.07-r19 ) | ||
| + | |||
| + | Notice: This updated is imported if you make use of the boxmode function. (Boxmode 1 is default and boxmode 12 activate PiP) | ||
| + | |||
| + | the update goes the same way as flashing a image. | ||
| + | The HD51 folder on the USB disc must be clean before placing the content of the zip file on the USB disk. | ||
| + | The zip file contains 2 files: '''hd51-bolt.bin''' and '''imageversion''' | ||
| + | |||
| + | There are two ways to place the boot loader on your receiver: | ||
| + | Option 1: Press the standby button for 15 seconds until BOLT appears on the display. | ||
| + | Option 2: Start your receiver via the power plug and hold the standby button until BOLT appears on the display. | ||
| + | |||
| + | The flash procedure will only take a few seconds and when Complete appears at the display, the receiver will restart. | ||
| + | Warning: Do not unplug the receiver during the update process! | ||
| + | |||
| + | Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/ | ||
Revision as of 21:55, 13 May 2017
Supported receivers
- HD51
- HD500C
- HD1100
- HD1200
- HD1265
- HD1500
- HD2400
How to flash the receiver...
Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.
FLASHING THE RECEIVER.
- Unzip compressed file.
- Copy the folder to a USB Pen Drive.
- Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
- Power on receiver with the mains switch on the rear.
- After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.
- Flashing of the image will start
- Booting will start automatically once the flashing process has completed
Note: In order to load the image automagically, rename the file called "noforce" to "force"
Specific information for HD51 New bootloader V1.07-r19 for Mut@nt HD51 model.
The file can be download at: http://downloads.mut...olt-v107r19.zip
To check with boot loader version you have... Enter the receiver with telnet, enter the following command:
#:/cat /sys/firmware/devicetree/base/bolt/tag ( bolt versie nummer opvragen: v1.07-r19 )
Notice: This updated is imported if you make use of the boxmode function. (Boxmode 1 is default and boxmode 12 activate PiP)
the update goes the same way as flashing a image. The HD51 folder on the USB disc must be clean before placing the content of the zip file on the USB disk. The zip file contains 2 files: hd51-bolt.bin and imageversion
There are two ways to place the boot loader on your receiver: Option 1: Press the standby button for 15 seconds until BOLT appears on the display. Option 2: Start your receiver via the power plug and hold the standby button until BOLT appears on the display.
The flash procedure will only take a few seconds and when Complete appears at the display, the receiver will restart. Warning: Do not unplug the receiver during the update process!
Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/
