Cable:Ziggo
Former UPC also known as Ziggo-East
If your contract/customer code does not start with a 1, then the following information is valid. Enter the following settings:
Frequency: 164.000
Symbolrate: 6900
Modulation: QAM256 - Note: This is changed since June 14th
Network ID: 05555 for FTV and Scrambled channels
Network ID: 04444 for FTV channels
Ziggo before the merger also known as Ziggo-West
If your contract/customer code start with a 1, then the following information is valid. Enter the following settings:
Frequency: 474.000
Symbolrate: 6875
Modulation: QAM64
Network ID: 05555 for FTV and Scrambled channels
Network ID: 04444 for FTV channels
At the Ziggo website: https://www.ziggo.nl/klantenservice/televisie-radio/digitale-tv/activeringscode-frequentie-netwerk-id-instellen/#netwerk-id-philips there is a notice that Philips TV sets from the year 2010 with the product type 6000 or higher, do not hold the network code 5555 for more than a few days. To workaround this problem Ziggo has kept the old network-ID's active. To continue watching channels, you must enter the following code:
| Region | Network-ID |
|---|---|
| Noord-Holland | 43136 |
| Flevoland | 43138 |
| Friesland | 43140 |
| Gelderland | 43142 |
| Brabant | 43144 |
| Zuid-Holland | 43146 |
| Alkmaar | 43192 |
| Alphen a/d Rijn | 43185 |
| Amersfoort | 43195 |
| Breda | 43191 |
| Capelle | 43194 |
| Den Bosch | 43198 |
| Den Haag | 43186 |
| Driebergen | 43189 |
| Emmen | 43208 |
| Gorichem | 43190 |
| Gorredijk | 43209 |
| Groningen | 43206 |
| Hengelo | 43211 |
| Hilversum | 43196 |
| Hoogeveen | 43205 |
| Mill | 43197 |
| Roermond | 43202 |
| Roosendaal | 43199 |
| Sassenheim | 43184 |
| Schoonbron | 43203 |
| Sneek | 43210 |
| Tilburg | 43200 |
| Utrecht | 43187 |
| Veenendaal | 43188 |
| Velsen | 43193 |
| Venlo | 43201 |
| Winschoten | 43207 |
| Zwolle | 43204 |
Note: Netwerk ID by hometown: (in case your hometown isn't mentioned try a city near your hometown.)
Obviously, of course, the entire cabling must comply with the current standard set by ziggo. In other words Cable tire A + (4g shielded) plugs, cables, splitters, plugs, amplifiers etc. The AOP (Subscriber Acquisition Point) must also comply with this. If this does not comply with this standard, there is a likelihood that, after the new channel format, low and high frequency transmitters will not appear in the scan. Among others Since the last change, the movie channels have been in almost the entire ziggo region at low frequencies.
A major mistake is that the cable connects to an outdated analogue wall socket. These old wall sockets, as well as the old cabling in the walls, often no longer meet the current Kabelkeur A + standard and therefore dampen the high and low frequencies. The only correct way is to connect the cable that is A + certified by cable directly to the AOP. The AOP should have a modern AOP equipped with the cable mark mark. AOPs without a quality mark often no longer meet.
