Data sharing

From OpenPLi Wiki
Revision as of 12:59, 23 May 2022 by WanWizard (talk | contribs) (No more guest access without password)
Jump to: navigation, search

Intro

Basically, if you want to share data in a computer network, there is a server and a client side or many clients. On de server side there needs to be a protocol that the client understands. Here you will have to choose between the NFS or CIFS (SMB/Samba) protocol to able to access the machine you want to connect to. If you want OpenPLi to access or store data on another machine in your network, you will need to add a new network mount point, this can be done in OpenPLi using the MountManager (see below). Here you will have to choose between the NFS or CIFS protocol to able to access the machine you want to connect to.

NOTE: When you create a new mount using mount manager as described below and save it, it is by default disabled!!


Background on NFS and CIFS (Samba/SMB)

NFS and CIFS are protocols to make a (data)connection between server and client.


NFS


NFS stands for Network File system and was created in 1984 by Sun Microsystems and (were) used for there Unix workstations.


CIFS


CIFS stands for Common Internet File System and was developed by Microsoft. It’s a kind of dialect of SMB (Samba) most people use these two SMB/CIFS together, but although they are different, they play well together. In comparison to NFS, CIFS tends to be a bit more "chatty" in its communication.


Autodetection


As of OpenPLi 7.2 CIFS config has SMB version and security protocol autodetection, so that you no longer have to start looking for whether options have to be given, they are now entered automatically, so practically it means that the suggestions below should not be needed anymore, the system will try all options until one setting works!!


No more guest access without password


As of OpenPLi 8.2 there is no more guest access without a password possible, this is because modern OS's are not allowing this any one.

If you have this in use, please change the mount definition, entering "guest" for username and/or password instead of leaving it blank, BEFORE you upgrade to OpenPLi 8.2 (or flash it and restoring old configuration).

If you don't, your box will hang after the start, until the mount attempt times out, which can take a long time (10 minutes or more).

Which protocol to use


Oversimplified you could say that you choose NFS between Unix/Linux machines and CIFS between Windows and Unix/Linux machines.


How to start


When you want to use NFS to access an OpenPLi box you will have to install "NFS server" on the server side. From the plugins, it is in de "extensions" section. If you want to access this new NFS server receiver from another OpenPLi receiver (the Client) you will need to configure the client using "MountManager" as explained below under NFS.

When you want to use CIFS (SMB/Samba) to access and OpenPLi box, you don't have to do anything on the server side, as CIFS is already "working". If you want to access this CIFS server receiver from another OpenPLi receiver (the Client) you will need to configure the client using "MountManager" as explained below under CIFS.


Server share and the difference between CIFS and NFS

When you add the server share, so like the location on a NAS you want access, there is a difference in the notation. For example if you want to access a shared folder named video on your Synology NAS which has a volume1, then with

NFS the Server share is:

/volume1/video

CIFS the Server share is

/video

When CIFS is not working

Old method (Only needed for versions of OpenPLi 7.1 and below)

If you can't create a mount, than some security settings may be not up-to-date. Maybe you are still using Samba version 1.0. Although you can make it work, remember still running Samba using version 1 can be a security risk. Follow this link if you are sure that still using Samba version 1.0 is not a security risk for you.

NFS

OpenPLi to OpenPLi


frameles
frameles

When you have OpenPLi installed on 2 boxes, it's easy to make a NFS share. To make this happen first install and configure the NFSserver extension/plugin from the feed on the server box (and reboot the box), then on the client box go to Menu > Setup > System > Expert settings > Network > MountManager and choose Add new network mount point. Here you will have to adjust 7 settings in order to make the connection a success.

  1. Active set it to Enable
  2. Local share name set it to any name you like (here I leave it as Sharename). It's the name you will see in OpenPLi when the share is a success.
  3. Mount type set it to NFS
  4. Server IP here you enter the IP Address of the machine you want to connect to, remember is should be a static or reserved one (meaning it does not change when this machine goes on or off)
  5. Server share if you haven't anything regarding the recording location then leave it at default so /media/hdd.
  6. Use as HDD replacement if you want this choose, yes else no
  7. Mount options leave it as it is.

Now save these settings by pressing OK on your remote. When this done go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Mountpoints management. You should see something like this and you can access the data in this shared.


OpenPLi to NAS


frameles
frameles

I assume the NAS uses a Linux distribution. Which is in most cases true, as Linux is free and that's favorable to manufacturer's business model. First you’ll have to set things right on the server side (NAS), check if NFS is active and grant the ip address of your OpenPLi box access to the NAS in the NFS settings of the NAS. When this is done In OpenPLi go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Add new network mount point. Here you will have to adjust 7 settings in order to make the connection a success.

  1. Active set it to Enable
  2. Local share name set it to any name you like (here I leave it as Sharename). It's the name you will see in OpenPLi when the share is a success.
  3. Mount type set it to NFS
  4. Server IP here you enter the IP Address of the machine you want to connect to, remember is should be a static or reserved one (meaning it does not change when this machine goes on or off)
  5. Server share here you will have to enter the exact name of the path to the folder/directory on the machine you want to access. Notice and take look at the pictures NFS has a different path that CIFS, although NFS and CIFS where setup to the same machine!
  6. Use as HDD replacement if you want this, choose yes else no
  7. Mount options mostly you can leave this as it is.

Now save these settings by pressing OK on your remote. When this done go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Mountpoints management. You should see something like this and you can access the data.


CIFS

OpenPLi to OpenPLi


frameles
frameles

Go to the OpenPLi box that will be the client, meaning the box that wants to have access to another OpenPLi receiver, then go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Add new network mount point. Here you will have to adjust 9 settings in order to make the connection a success.

  1. Active set it to Enable
  2. Local share name set it to any name you like (here I leave it as Sharename). It's the name you will see in OpenPLi when the share is a success.
  3. Mount type set it to CIFS
  4. Server IP here you enter the IP Address of the machine you want to connect to, remember is should be a static or reserved one (meaning it does not change when this machine goes on or off)
  5. Server share here you will have to enter the exact name of the path to the folder/directory on the machine you want to access.
  6. Use as HDD replacement if you want this, choose yes else no
  7. Mount options mostly you can leave this as it is.
  8. User name default is guest, leave it at that
  9. Password default is *, leave it at that

Now save these settings by pressing OK on your remote. When this done go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Mountpoints management. You should see something like this and you can access the data.

OpenPLi to NAS


frameles
frameles

On the NAS check if SMB/CIFS is active and give access to a username and password or give guest access. Next go to the OpenPLi box and go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Add new network mount point. Here you will have to adjust 9 settings in order to make the connection a success.

  1. Active set it to Enable
  2. Local share name set it to any name you like (here I leave it as Sharename). It's the name you will see in OpenPLi when the share is a success.
  3. Mount type set it to CIFS
  4. Server IP here you enter the IP Address of the machine you want to connect to, remember is should be a static or reserved one (meaning it does not change when this machine goes on or off)
  5. Server share here you will have to enter the exact name of the path to the folder/directory on the machine you want to access. Notice and take look at the pictures CIFS has a different path than NFS, although NFS and CIFS where setup to the same machine!
  6. Use as HDD replacement if you want this, choose yes else no
  7. Mount options mostly you can leave this as it is.
  8. User name default is guest, leave it at that
  9. Password default is *, leave it at that

Now save these settings by pressing OK on your remote. When this done go to Menu > Setup > System > Expert settings > Network > MountManager and then choose Mountpoints management. You should see something like this and you can access the data.

OpenPLi to a Windows computer

Here is explained how to access/add a shared folder that's on a Windows PC

On the Windows machine

In Windows you need to create a shared folder, you can do that for guest or everyone and choose to have passwords or not. After you created the shared folder with or without username or password, you will have to enter these in OpenPLi, you will also need the IP address of the Windows machine and the folder that you shared, so write these down.

On the OpenPLi receiver

1.Use your remote control and go to Main menu > Setup > System > Expert settings > Network > MountManager

2.Add new network mount point

frameles


3. Active: change the slider to green

frameles


frameles


4.Local mountpoint: Leave this as it is (you can change this later if you want)


5.Mount type: Change it from NFS to CIFS (arrow to the left)

frameles


6.Server IP: Enter the ip address of your Windows computer

frameles


7.Hostname: Leave this as it is, so empty


8.Server share: this is the name of the folder you shared on your Windows PC. Keep in mind that when the shared folder is in

/folder/shared folder 

you only have to enter

shared folder 

so not the complete path (This is a Windows thingy ;))

frameles


9.Username: When you have created a windows share with a username enter this, when you have set windows share without a username then leave this as it is, so guest


10.Password: When you have created a windows share with a password enter this, when you have set windows share without a password then leave this as it is, so *


11.Now press Ok on your remote control and if you entered everything correct then the share to your Windows PC should be active, the little world icon should now be green
frameles


12.Exit the mount manager and press the PVR or the Playlist on your remote (will be different per receiver or remote) and now you should be able to see the files on the Windows PC, please remember that not all files types can be displayed, as your receiver is a Linux machine accessing a Windows machine, but most movie file types should be recognized.

frameles