Difference between revisions of "Receivers:Mut@nt"

From OpenPLi Wiki
Jump to: navigation, search
Line 25: Line 25:
  
 
<u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force"
 
<u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force"
 +
 +
----
 +
Specific information for HD51
 +
New bootloader V1.07-r19 for Mut@nt HD51 model.
 +
 +
The file can be download at: http://downloads.mut...olt-v107r19.zip
 +
 +
To check with boot loader version you have... Enter the receiver with telnet, enter the following command:
 +
#:/cat /sys/firmware/devicetree/base/bolt/tag ( bolt versie nummer opvragen: v1.07-r19 )
 +
 +
Notice: This updated is imported if you make use of the boxmode function. (Boxmode 1 is default and boxmode 12 activate PiP)
 +
 +
the update goes the same way as flashing a image.
 +
The HD51 folder on the USB disc must be clean before placing the content of the zip file on the USB disk.
 +
The zip file contains 2 files: '''hd51-bolt.bin''' and '''imageversion'''
 +
 +
There are two ways to place the boot loader on your receiver:
 +
Option 1: Press the standby button for 15 seconds until BOLT appears on the display.
 +
Option 2: Start your receiver via the power plug and hold the standby button until BOLT appears on the display.
 +
 +
The flash procedure will only take a few seconds and when Complete appears at the display, the receiver will restart.
 +
Warning: Do not unplug the receiver during the update process!
 +
 +
Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/

Revision as of 21:55, 13 May 2017

Supported receivers

RECEIVER-Mutant-001.jpg
  • HD51
  • HD500C
  • HD1100
  • HD1200
  • HD1265
  • HD1500
  • HD2400

How to flash the receiver...

Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

FLASHING THE RECEIVER.

  1. Unzip compressed file.
  2. Copy the folder to a USB Pen Drive.
  3. Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
  4. Power on receiver with the mains switch on the rear.
  5. After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.
  6. Flashing of the image will start
  7. Booting will start automatically once the flashing process has completed

Note: In order to load the image automagically, rename the file called "noforce" to "force"


Specific information for HD51 New bootloader V1.07-r19 for Mut@nt HD51 model.

The file can be download at: http://downloads.mut...olt-v107r19.zip

To check with boot loader version you have... Enter the receiver with telnet, enter the following command:

#:/cat /sys/firmware/devicetree/base/bolt/tag ( bolt versie nummer opvragen: v1.07-r19 )

Notice: This updated is imported if you make use of the boxmode function. (Boxmode 1 is default and boxmode 12 activate PiP)

the update goes the same way as flashing a image. The HD51 folder on the USB disc must be clean before placing the content of the zip file on the USB disk. The zip file contains 2 files: hd51-bolt.bin and imageversion

There are two ways to place the boot loader on your receiver: Option 1: Press the standby button for 15 seconds until BOLT appears on the display. Option 2: Start your receiver via the power plug and hold the standby button until BOLT appears on the display.

The flash procedure will only take a few seconds and when Complete appears at the display, the receiver will restart. Warning: Do not unplug the receiver during the update process!

Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/