Difference between revisions of "Receivers:Mut@nt"

From OpenPLi Wiki
Jump to: navigation, search
(How make a Multiboot for a HD51)
m (USB stick needs to have an MBR partition table, most boxes don't support GPT)
 
(16 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
[[File:RECEIVER-Mutant-001.jpg|frameless|right]]
 
[[File:RECEIVER-Mutant-001.jpg|frameless|right]]
 +
 +
=='''Preparations'''<br />==
 +
Format your USB stick with an MBR partition table and a FAT32 file system.<br />
 +
Download a image from: https://openpli.org/download/mutant<br />
 +
Unpack the ZIP file and place the content on the USB stick.<br />
  
 
=='''How to flash the new HD 60 UHD receiver...'''<br />==
 
=='''How to flash the new HD 60 UHD receiver...'''<br />==
  
Flashing the Receiver.
+
FLASHING THE RECEIVER.
 
# Power off the receiver
 
# Power off the receiver
 
# Insert the USB stick containing the image files into one of the USB ports on the receiver.
 
# Insert the USB stick containing the image files into one of the USB ports on the receiver.
Line 17: Line 22:
 
=='''How to flash the HD 51 receiver...'''<br />==
 
=='''How to flash the HD 51 receiver...'''<br />==
  
Flashing the Receiver.
+
FLASHING THE RECEIVER. <br />
 
# Power off the receiver
 
# Power off the receiver
 
# Ensure no other USB devices are plugged into the receiver while flashing.
 
# Ensure no other USB devices are plugged into the receiver while flashing.
Line 31: Line 36:
 
=='''How to flash the other receivers...'''<br />==
 
=='''How to flash the other receivers...'''<br />==
  
Download a image from: https://openpli.org
+
FLASHING THE RECEIVER.
Unpack the ZIP file and place the content on a USB disk.
+
# Unzip compressed file.
 
+
# Copy the folder to a USB Pen Drive.
FLASHING THE RECEIVER. <br />
+
# Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
# Unzip compressed file.<br />
+
# Power on receiver with the mains switch on the rear.
# Copy the folder to a USB Pen Drive.<br />
+
# After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.
# Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.<br />
+
# Flashing of the image will start.
# Power on receiver with the mains switch on the rear.<br />
+
# Booting will start automatically once the flashing process has completed.
# After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.<br />
 
# Flashing of the image will start<br />
 
# Booting will start automatically once the flashing process has completed<br />
 
  
 
<u>Note:</u> In order to load the image automatically, rename the file called "noforce" to "force"
 
<u>Note:</u> In order to load the image automatically, rename the file called "noforce" to "force"
 
  
  
 
'''Specific information for HD51''' new bootloader V1.07-r19.
 
'''Specific information for HD51''' new bootloader V1.07-r19.
 
----  
 
----  
The file can be download at: http://downloads.mut...olt-v107r19.zip
+
The file can be download at: http://downloads.mutant-digital.net/bootloader/hd51-bolt-v107r19.zip
  
  
Line 116: Line 117:
 
=='''How make a Multiboot for a HD51'''<br />==
 
=='''How make a Multiboot for a HD51'''<br />==
  
#The multiboot image cannot be flashed via USB (on this box). You can only flash it from a running e2 or from command line, so flashing is preferably done from the [[Installation#Flash_from_the_Menu_.28FlashImage_support.29 | <span style="color:SteelBlue"> menu</span>]]. This image can be installed in each of the multiboot slots.
+
#If you want to add any other images, well other than OpenPLi so for example OpenATV, then you download there image zip file for your receiver, <u>do not unpack this zip file</u>, so keep it intact and copy it to the root
 +
USB Drive(d):/openatv-6.4-mutant51-20210117_usb.zip
 +
of an USB stick. Insert this USB stick with the zip file on it in the usb port of your receiver. Then use the flash from the [[Installation#Flash_from_the_Menu_.28FlashImage_support.29 | <span style="color:SteelBlue"> menu</span>]] procedure. When you go to Main menu -> Setup -> Flash image open the "Downloaded Images" here you will find the zip file you copied to the usb stick.

Latest revision as of 14:21, 26 October 2023

RECEIVER-Mutant-001.jpg

Preparations

Format your USB stick with an MBR partition table and a FAT32 file system.
Download a image from: https://openpli.org/download/mutant
Unpack the ZIP file and place the content on the USB stick.

How to flash the new HD 60 UHD receiver...

FLASHING THE RECEIVER.

  1. Power off the receiver
  2. Insert the USB stick containing the image files into one of the USB ports on the receiver.
  3. Push and hold the small button next to the TF card slot at the lift side of the box.
  4. Power the receiver on.
  5. After a short while the red power led at the front starts to blink. Now you can release the button.
  6. If successful the receiver will reboot it self after the flashing process has completed.
  7. During the setup process you will be requested to restore a previous backup in case you have made one on your USB stick.

The flashing process should take approximately 1.5 minutes to complete, while the receiver is being flashed, it is important that you DO NOT power the receiver down for any reason as this can cause serious and or permanent damage.


How to flash the HD 51 receiver...

FLASHING THE RECEIVER.

  1. Power off the receiver
  2. Ensure no other USB devices are plugged into the receiver while flashing.
  3. Insert the USB stick containing the image files into one of the USB ports on the receiver, rear USB port is advised if possible.
  4. Power the receiver on.
  5. Immediately after powering on PRESS AND HOLD the front power button until ‘flashing..’ appears on front display.
  6. If successful the receiver will reboot it self after the flashing process has completed.
  7. Remove USB stick that contains the images files.

The flashing process should take approximately two to four minutes to complete, while the receiver is being flashed, it is important that you DO NOT power the receiver down for any reason as this can cause serious and or permanent damage.


How to flash the other receivers...

FLASHING THE RECEIVER.

  1. Unzip compressed file.
  2. Copy the folder to a USB Pen Drive.
  3. Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
  4. Power on receiver with the mains switch on the rear.
  5. After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.
  6. Flashing of the image will start.
  7. Booting will start automatically once the flashing process has completed.

Note: In order to load the image automatically, rename the file called "noforce" to "force"


Specific information for HD51 new bootloader V1.07-r19.


The file can be download at: http://downloads.mutant-digital.net/bootloader/hd51-bolt-v107r19.zip


The easy way to check the bootloader version is by going to Menu > Information > About

Alternative using the CLI to check the bootloader version you have... Enter the receiver with telnet, enter the following command:

#:/cat /sys/firmware/devicetree/base/bolt/tag

Notice: This update is imported if you make use of the boxmode function. (Boxmode 1 is default and boxmode 12 activate PiP)

the update goes the same way as flashing a image. The HD51 folder on the USB disc must be clean before placing the content of the zip file on the USB disk. The zip file contains 2 files: hd51-bolt.bin and imageversion

There are two ways to place the boot loader on your receiver: Option 1: Press the standby button for 15 seconds until BOLT appears on the display. Option 2: Start your receiver via the power plug and hold the standby button until BOLT appears on the display.

The flash procedure will only take a few seconds and when Complete appears at the display, the receiver will restart. Warning: Do not unplug the receiver during the update process!

Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/


Remark: When usesing the HD51 as a 4k receiver do not set the AV mode (Resolution of the screen) other than 50Hz. When the signal receives 60Hz the receiver disrupts the TV output. In most cases the display is black and a restart of the receiver is needed to regain TV functionality.


Boxmode for HD51 how to...


There are currently two box mode options for the HD51.

  • Mode 1 = 2 video encoder for main screen
  • Mode 12 = 2 video encoder for main screen + 1 video encoder for 2nd screen (PiP)

To alter your receiver into a different box mode Goto folder: /media/mmc/STARTUP default:

boot emmcflash0.kernel1 'root=/dev/mmcblk0p3 rw rootwait hd51_4.boxmode=1'

if you alter hd51_4.boxmode=1 into 12, your receiver is switching to boxmode 12 when you restart your receiver. so:

boot emmcflash0.kernel1 'root=/dev/mmcblk0p3 rw rootwait hd51_4.boxmode=12'

Must I switch from mode? The answer is no. If you switching into box mode 12, the energy consumption will increase.

Source: https://forums.openpli.org/topic/43945-hd51-bootloader-v107/


Specific information for HD2400


Bootloader V36 (Available since may 2015), supports images up to 500MB, support multi boot by kexec, support systemd images, support images startup from USB, SSD, HDD and SDcard.

Before you install the new bootloader, please been certain there is no map called /hd2400 on your USB stick.It can happen that the bootloader will not install when a splash or force file is in the /hd2400 map.

Follow the next steps to successful update the bootloader.

  1. Remove the map /hd2400 when it's already on your USB stick.
  2. Unzip the file to an USB stick. (You will see a map called /hd2400 with 2 files image version and hd2400-cfe.bin)
  3. Place the USB stick in an USB socket of the HD2400.
  4. Start the box with the power switch at the back of the box.
  5. The display will show a message, to load the new bootloader you will need to press the second button which has a down arrowhead (V) symbol.
  6. The display will show flashing for about 10 seconds and after this the HD2400 will reboot automatically.


How make a Multiboot for a HD51

  1. If you want to add any other images, well other than OpenPLi so for example OpenATV, then you download there image zip file for your receiver, do not unpack this zip file, so keep it intact and copy it to the root
USB Drive(d):/openatv-6.4-mutant51-20210117_usb.zip

of an USB stick. Insert this USB stick with the zip file on it in the usb port of your receiver. Then use the flash from the menu procedure. When you go to Main menu -> Setup -> Flash image open the "Downloaded Images" here you will find the zip file you copied to the usb stick.