Difference between revisions of "Wetek"

From OpenPLi Wiki
Jump to: navigation, search
(Created page with "'''Supported receivers'''<br /> frameless|right * Play<br /> '''How to flash the receiver...'''<br /> Download a image from: https://openpli...")
 
Line 9: Line 9:
 
Unpack the ZIP file and place the content on a USB disk.
 
Unpack the ZIP file and place the content on a USB disk.
  
FLASHING THE RECEIVER. <br />
+
1. Place the USB disk or mSD-card into the slot of the Wetek and remove the power cable.
 +
2. Look at the back side and press, with the supplied tool, the '''Upgrade''' button and keep this button pressed for approx 10 seconds during you place the power cable back in the receiver.
 +
3. Wait for a minut and you'll see the following screen:
  
Haal de volgende bestanden uit het gedownloade bestand "OpenPLi-4.0-beta-20160203_NAND.7z" ...
+
[[File:RECEIVER-Wetek-flash001.jpg]]
 
- factory_update_param.aml
 
- recovery.img
 
- OpenPLi-4.0-beta-wetekplay-20160203_nand.zip
 
  
...en kopieer ze naar een USB-stick of mSD-card.
+
4. Move the cursor down with the usage of the remote control and select '''Apply update from EXT'''.
  
 +
[[File:RECEIVER-Wetek-flash002.jpg]]
  
Plaats de stick of mSD-card in het slot van de Wetek, verwijder de spanningkabel.
+
5. Press the OK button from the remote control and select in the next screen '''Update from udisk'''.
  
Draai de box om, druk met behulp van het bijgeleverde hulpmiddel de "Upgrade" knop in en houd deze ongeveer 10 sec ingedrukt terwijl je de spanningskabel weer aansluit.
+
[[File:RECEIVER-Wetek-flash003.jpg]]
  
Wacht een minuutje en het volgende scherm verschijnt;
+
6. Select in the next screen the OpenPLi file
  
{{image url="http://i533.photobucket.com/albums/ee338/hauselito/OpenPli2Nand%20%2001.jpg"}}
+
[[File:RECEIVER-Wetek-flash004.jpg]]
  
Beweeg de cursor naar beneden m.b.v de afstandsbediening en selecteer "Apply update from EXT";
+
7. Press the OK button and the flashing procedure starts. Wait until the next screen:
  
{{image url="http://i533.photobucket.com/albums/ee338/hauselito/OpenPli2Nand%20%2002.jpg"}}
+
[[File:RECEIVER-Wetek-flash005.jpg]]
  
Druk op OK van de afstandsbediening en selecteer in het volgende scherm "Update from udisk"
+
8. Press the OK button and the first screen reappears.  
 
+
9. Select '''Reboot system now'''
{{image url="http://i533.photobucket.com/albums/ee338/hauselito/OpenPli2Nand%20%2003.jpg"}}
+
10. The Wetek receiver starts now like a Enigma2 receiver
 
 
Kies in het volgende scherm het OpenPli bestand;
 
 
 
{{image url="http://i533.photobucket.com/albums/ee338/hauselito/OpenPli2Nand%20%2004.jpg"}}
 
 
 
Druk op OK en het programmeren begint, wacht tot je het volgende scherm ziet;
 
 
 
{{image url="http://i533.photobucket.com/albums/ee338/hauselito/OpenPli2Nand%20%2006.jpg"}}
 
 
 
Druk op OK en het eerste scherm verschijnt weer, kies hier voor "Reboot system now"
 
 
 
Je Wetek box start nu op als een Enigma2 ontvanger, dat was het.
 

Revision as of 20:09, 23 May 2017

Supported receivers

RECEIVER-Wetek-001.png
  • Play

How to flash the receiver...

Download a image from: https://openpli.org Unpack the ZIP file and place the content on a USB disk.

1. Place the USB disk or mSD-card into the slot of the Wetek and remove the power cable. 2. Look at the back side and press, with the supplied tool, the Upgrade button and keep this button pressed for approx 10 seconds during you place the power cable back in the receiver. 3. Wait for a minut and you'll see the following screen:

RECEIVER-Wetek-flash001.jpg

4. Move the cursor down with the usage of the remote control and select Apply update from EXT.

RECEIVER-Wetek-flash002.jpg

5. Press the OK button from the remote control and select in the next screen Update from udisk.

RECEIVER-Wetek-flash003.jpg

6. Select in the next screen the OpenPLi file

RECEIVER-Wetek-flash004.jpg

7. Press the OK button and the flashing procedure starts. Wait until the next screen:

RECEIVER-Wetek-flash005.jpg

8. Press the OK button and the first screen reappears. 9. Select Reboot system now 10. The Wetek receiver starts now like a Enigma2 receiver