Difference between revisions of "Zgemma"

From OpenPLi Wiki
Jump to: navigation, search
(How to flash Zgemma H9 Combo/Twin)
(How to flash Zgemma H9 Combo/Twin SE)
Line 69: Line 69:
 
Download an image from: https://openpli.org/download/zgemma/H9+Combo+SE
 
Download an image from: https://openpli.org/download/zgemma/H9+Combo+SE
  
# Use a USB stick with FAT32 format.
+
# Download both the recovery_emmc and emmc zip file from the OpenPli website
# Copy both emmc ZIP files to the USB stick, do NOT unpack them!
+
# Do NOT unpack these files but copy these zip files to your USB stick.
# Power off the receiver
+
# Place USB in the box while power off.
# Plug the USB stick to one of the back panel USB ports. Recommended to remove all other USB connected devices.
+
# Turn on the device at the back en PRESS AND HOLD the POWER BUTTON on THE REMOTE until the recovery menu appears
# Power the receiver on whilst holding down the POWER ON BUTTON on the remote.
+
# Now flash the recovery_emmc zip first
# Only release the power button when the box is in flash mode.
+
# Repeat procedure and flash the emmc image file to 'linux slot 1'
# If successful the receiver will reboot it self after the flashing process has completed.
+
# After flashing, the box will restart in the recovery menu
# Remove USB stick
+
# Select 'linux slot 1' to start the flashed image
  
 
=='''How to flash Zgemma H9 S/2S/2H SE'''<br />==
 
=='''How to flash Zgemma H9 S/2S/2H SE'''<br />==

Revision as of 09:14, 3 June 2021

RECEIVER-Zgemma-001.png

How to flash Zgemma H1/2S/H2/S

Download a image from: https://openpli.org

  1. Format your USB stick with a FAT32 file system
  2. Unpack the ZIP file and place the content on a USB disk.
  3. Plug the USB stick to the back panel USB port.
  4. Power on,
  5. Press the Power Key on the front panel after you see “USB”on the display. Then the display shows “Flash”
  6. When done the box will boot up on its own.
  7. Remove usb stick once boot has completed.


How to flash a Zgemma I55 IPTV device.

Download a image from: https://openpli.org/download/zgemma/I55/

  1. Format your USB stick with a FAT32 file system
  2. Unpack the ZIP file and place the content on a USB disk.
  3. Change the name of the file 'Noforce' to 'force' and disconnect the stick.
  4. Plug the USB stick to the USB port at the right side of the I55.
  5. Power on the box,
  6. The Red led on the front lights once. After about 2 min it light again.
  7. When done the box will boot up on its own.
  8. Remove usb stick once boot has completed.
  9. After you have configured the basic things like Language, video and lan you choose to download plugins.
  10. Basically the only plugin you need is RemoteStreamConvert to let the I55 do his job.


How to flash Zgemma H7S/C/AC

Download an image from: https://openpli.org/download/zgemma/H7.S

  1. Use a USB stick with FAT32 format.
  2. Unpack the ZIP file to the USB stick.
  3. You should see a "zgemma" folder in the root of the USB stick.
  4. Power off your receiver.
  5. Plug the USB stick to one of the back panel USB ports. Recommended to remove all other USB connected devices.
  6. Power on
  7. Immediately after power on PRESS AND HOLD the front power button behind front flap.
  8. The display will show boot, USB, FLSH. Once FLSH is displayed you can release (stop pressing) the button.
  9. Wait, when "boot" is displayed you can remove the USB stick

How to flash Zgemma H9.2H/S /H9S/T

Download an image from: https://openpli.org/download/zgemma/H9.2H

  1. Use a USB stick with FAT32 format.
  2. Unpack the ZIP file to the USB stick.
  3. You should see a "zgemma" folder in the root of the USB stick.
  4. Power off the receiver
  5. Plug the USB stick to one of the back panel USB ports. Recommended to remove all other USB connected devices.
  6. Power the receiver on whilst holding down the REAR RESET BUTTON
  7. Once the front Air Digital display logo start to flash White/Red, release the rear reset button and wait, your receiver is now being flashed.
  8. If successful the receiver will reboot it self after the flashing process has completed.
  9. Remove USB stick

How to flash Zgemma H9 Combo/Twin

Download an image from: https://openpli.org/download/zgemma/H9+Combo

  1. Download both the recovery_emmc and emmc zip file from the OpenPli website
  2. Do NOT unpack these files but copy these zip files to your USB stick.
  3. Place USB in the box while power off.
  4. Turn on the device at the back en PRESS AND HOLD the POWER BUTTON on THE REMOTE until the recovery menu appears
  5. Now flash the recovery_emmc zip first
  6. Repeat procedure and flash the emmc image file to 'linux slot 1'
  7. After flashing, the box will restart in the recovery menu
  8. Select 'linux slot 1' to start the flashed image

How to flash Zgemma H9 Combo/Twin SE

Download an image from: https://openpli.org/download/zgemma/H9+Combo+SE

  1. Download both the recovery_emmc and emmc zip file from the OpenPli website
  2. Do NOT unpack these files but copy these zip files to your USB stick.
  3. Place USB in the box while power off.
  4. Turn on the device at the back en PRESS AND HOLD the POWER BUTTON on THE REMOTE until the recovery menu appears
  5. Now flash the recovery_emmc zip first
  6. Repeat procedure and flash the emmc image file to 'linux slot 1'
  7. After flashing, the box will restart in the recovery menu
  8. Select 'linux slot 1' to start the flashed image

How to flash Zgemma H9 S/2S/2H SE

Download an image from: https://openpli.org/download/zgemma/H9.2H+SE

  1. Use a USB stick with FAT32 format.
  2. Copy both emmc ZIP files to the USB stick, do NOT unpack them!
  3. Power off the receiver
  4. Plug the USB stick to one of the back panel USB ports. Recommended to remove all other USB connected devices.
  5. Power the receiver on whilst holding down the POWER ON BUTTON on the remote.
  6. Only release the power button when the box is in flash mode.
  7. If successful the receiver will reboot it self after the flashing process has completed.
  8. Remove USB stick