Difference between revisions of "Receivers:Xtrend"

From OpenPLi Wiki
Jump to: navigation, search
m (USB stick needs to have an MBR partition table, most boxes don't support GPT)
 
(20 intermediate revisions by 3 users not shown)
Line 2: Line 2:
  
 
[[File:RECEIVERS-Xtrend-001.png|frameless|right]]
 
[[File:RECEIVERS-Xtrend-001.png|frameless|right]]
* ET4x00<br />
 
* ET5x00<br />
 
* ET6000<br />
 
* ET6500<br />
 
* ET7000<br />
 
* ET7500<br />
 
* ET8000<br />
 
* ET8500<br />
 
* ET9000<br />
 
* ET9200<br />
 
* ET9500<br />
 
* ET10000<br />
 
  
Broken Securityboard? [https://wiki.openpli.org/index.php/Receivers:Xtrend_Securityboard Here] is a repair instruction. (Not confirmed yet and in the German Language)
+
=='''Broken Securityboard?'''==
 +
[[Receivers:Xtrend_Securityboard | Here]] is a repair instruction. (Not confirmed yet) or try the new drivers look at take a look in the forum Looking for our [https://forums.openpli.org <span style="color:SteelBlue"> Forum </span>]
  
'''How to flash the receiver...'''<br />
 
  
Download a image from: https://openpli.org
+
 
 +
=='''How to flash the receiver...'''<br />==
 +
 
 +
Format your USB stick with an MBR partition table and a FAT32 file system.<br />
 +
Download a image from: https://openpli.org/download/xtrend.
 
Unpack the ZIP file and place the content on a USB disk.
 
Unpack the ZIP file and place the content on a USB disk.
  
Line 32: Line 24:
  
 
<u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force"
 
<u>Note:</u> In order to load the image automagically, rename the file called "noforce" to "force"
 +
 +
<u>'''Note:'''</u> When using a rotor unit on a ET8500 receiver, do not put the rotor on tuner 3 or 4. Somehow the rotor command's are not transmitted correctly so moving the dish isn't working. So put the rotor on tuner 1 or 2.
 +
 +
=='''How to flash the receiver ET7x00...'''<br />==
 +
 +
Flashing the Receiver.
 +
 +
# Power off the receiver
 +
# Ensure no other USB devices are plugged into the receiver while flashing.
 +
# Insert the USB stick containing the image files into one of the USB ports on the receiver, rear USB port is advised if possible.
 +
# Power the receiver on, you will now see a RED LED.
 +
# When the RED LED BLINKS after 2-3 seconds press the FRONT STANDBY button located on the front panel of the receiver to start the flashing process, a GREEN LED will also appear to indicate that the flashing is in progress.
 +
# During the flashing process both the GREEN LED and RED LED will remain alight.
 +
# Once complete the receiver will automatically boot into the new image.
 +
 +
The flashing process should take approximately two to four minutes to complete, while the receiver is being flashed, it is important that you DO NOT power the receiver down for any reason as this can cause serious and or permanent damage.
 +
 +
 +
=='''ET6000 bootloader'''==
 +
If for some reason you want to install the [[Problems_and_Solutions#ET7000| <span style="color:SteelBlue"> bootloader</span>]].
 +
 +
Source: https://forums.openpli.org/index.php?app=core&module=attach&section=attach&attach_id=132322
 +
 +
=='''ET7000 bootloader'''==
 +
If for some reason you want to install the [[Problems_and_Solutions#ET7000| <span style="color:SteelBlue"> bootloader</span>]].
 +
 +
Source: https://forums.openpli.org/index.php?app=core&module=attach&section=attach&attach_id=132262

Latest revision as of 14:36, 26 October 2023

Supported receivers

RECEIVERS-Xtrend-001.png

Broken Securityboard?

Here is a repair instruction. (Not confirmed yet) or try the new drivers look at take a look in the forum Looking for our Forum


How to flash the receiver...

Format your USB stick with an MBR partition table and a FAT32 file system.
Download a image from: https://openpli.org/download/xtrend. Unpack the ZIP file and place the content on a USB disk.

FLASHING THE RECEIVER.

  1. Unzip compressed file.
  2. Copy the "etxxxx" folder to a USB Pen Drive.
  3. Power off or reboot the receiver with the mains switch on the rear. Connect USB Pen Drive.
  4. Power on receiver with the mains switch on the rear.
  5. After rebooting or cold start the power LED will blink several times after some time. At that moment press the power button on the front panel.
  6. Flashing of the image will start
  7. Booting will start automatically once the flashing process has completed

Note: In order to load the image automagically, rename the file called "noforce" to "force"

Note: When using a rotor unit on a ET8500 receiver, do not put the rotor on tuner 3 or 4. Somehow the rotor command's are not transmitted correctly so moving the dish isn't working. So put the rotor on tuner 1 or 2.

How to flash the receiver ET7x00...

Flashing the Receiver.

  1. Power off the receiver
  2. Ensure no other USB devices are plugged into the receiver while flashing.
  3. Insert the USB stick containing the image files into one of the USB ports on the receiver, rear USB port is advised if possible.
  4. Power the receiver on, you will now see a RED LED.
  5. When the RED LED BLINKS after 2-3 seconds press the FRONT STANDBY button located on the front panel of the receiver to start the flashing process, a GREEN LED will also appear to indicate that the flashing is in progress.
  6. During the flashing process both the GREEN LED and RED LED will remain alight.
  7. Once complete the receiver will automatically boot into the new image.

The flashing process should take approximately two to four minutes to complete, while the receiver is being flashed, it is important that you DO NOT power the receiver down for any reason as this can cause serious and or permanent damage.


ET6000 bootloader

If for some reason you want to install the bootloader.

Source: https://forums.openpli.org/index.php?app=core&module=attach&section=attach&attach_id=132322

ET7000 bootloader

If for some reason you want to install the bootloader.

Source: https://forums.openpli.org/index.php?app=core&module=attach&section=attach&attach_id=132262