Difference between revisions of "Problems and Solutions"
(→Time, if you have problems getting the correct time)
|Line 116:||Line 116:|
''extensions'' section of the [[Plugin_Wiki| <span style="color:SteelBlue">plugin browser</span>]].
''extensions'' section of the [[Plugin_Wiki| <span style="color:SteelBlue">plugin browser</span>]].
Revision as of 11:55, 26 August 2019
- 1 Alternative numbering mode
- 2 Brand\Vendor related
- 3 CI module with softcam (eg. OScam), so using both and making them work together
- 4 Crash logs
- 5 Debugging Enigma
- 6 Flickering dashed line in screen
- 7 Harddisk Check
- 8 I cannot record with my receiver or recording with a Zapper (eg. Vu Zero / Vu Solo Se)
- 9 Mountmanager Problems
- 10 Reset lost password
- 11 Splash screen replacement
- 12 Time, if you have problems getting the correct time
- 13 USB memory sticks working or not
- 14 Video codecs and what if you can not play a movie on your receiver
Alternative numbering mode
Are you confronted with channellist (bouquet) that don't start with the number 1, then enable this and it will. Goto Main Menu -> Setup -> System -> GUI Settings -> User Interface and enable "Alternative numbering mode"
Cable Scan issue's?
There is bug with the VU+ drivers so that a scan can not be completed if tuner D is used.
This is the issue: input3 and input2 have no input3_choices or input4_choices so the Enigma2 doesn't try to initialize them.
/proc/stb/tsmux/input1_choices:CI0 CI1 A B /proc/stb/tsmux/input0_choices:CI0 CI1 A B /proc/stb/tsmux/input3:A /proc/stb/tsmux/input2:A /proc/stb/tsmux/input1:B /proc/stb/tsmux/input0:AA simple solution is to initialize them manually.
Temporary solution until reboot
echo -n C > /proc/stb/tsmux/input2 echo -n D > /proc/stb/tsmux/input3
Note: VU+ should add input2_choices and input3_choices nodes.
Temporary Solution, that still works after a reboot: Install the IPK files that are posted at: https://forums.openpli.org/topic/49214-vuplus-duo2-dvb-t2-tuner-nim-tt3l10-stopped-working/page-3#entry701207 Reboot the receiver, and the scan problems are solved.
Restore Splash screen for - Factory bootlogo
The file that can be found at the forum (see below) will place the original factory bootlogo back on your receiver. The content of the file needs to be placed on a USB pen drive. The file contains splash screens for the models:
duo2, solo2, solo4k, solose, ultimo, ultimo4k, vuduo4k, uno, uno4k, uno4kse, zero and the zero4k.
You do not have to pick one of the bootlogo's.. Your receiver selects only the file that must be needed. .
So the following steps must be taken:
- place the content of the zip file on the USB pendrive
- reboot your receiver
- flash the 'image' (this wil take a few seconds)
- when the flash is completed, remove the USB pendrive
- restart your receiver
Restore Splash screen for Zgemma
Restore Splash screen for Edision
CI module with softcam (eg. OScam), so using both and making them work together
If for some reason you want to use a CI module and OScam, you will probably run into error messages. The problem or better the errors are there because CI modules are designed to work standalone. So if you want to make them working together, best practice is using the "Commoninterfaceassignment plugin”. So to let a CI work together with a softcam download and install "Commoninterfaceassignment plugin" which is located in the system section of the Plugin browser. After installing the plugin goto Menu-> Setup -> SoftCam/CI -> Common Interface Assignment and define every channel for this CI module, that you have a subscription for. Enigma2 (OpenPLi) will then send all the other channels to the Softcam (OScam) and not to the CI module.
Crash logs are generated during a system crash, also known as a GSOD (green screen of death). The log can give insight to the probable cause of the crash. If you want help with the content of the file, you can post it on our forum. The crash log file is named like in the example below:
The location of the crash log file when there is a HDD (Harddisk) present
Normally the crash.log file is stored in the root of the HDD so in
The location of the crash.log file without any HDD (Harddisk) present
Normally the crash log file is stored in the
If you want to debug and want to know what is happening in Enigma, you can start your receiver in debug mode with the following command:
root@<receiver>: init 4 root@<receiver>: ENIGMA_DEBUG_LVL=4 enigma2
To stop: Press CRTL-C. Enigma will halt. Then start enigma with:
root@<receiver>: init 3
Or reboot the receiver with:
Note: For debugging gstreamer with read actions stuff use: ENIGMA_DEBUG_LVL=4 GST_DEBUG=*soup*:6,*dvb*:6 enigma2
For easier reading (Less logging) use:
ENIGMA_DEBUG_LVL=4 GST_DEBUG=*soup*:4,*dvb*:4 enigma2
Writing debug log to a USB stick
If for some reason your receiver reboots your debug log might be gone. Then plugin a USB stick in your receiver and use the command below, which writes the debug log to and USB stick
ENIGMA_DEBUG_LVL=4 enigma2 | tee /media/usb/enigma.log
Flickering dashed line in screen
When you see a dashed flickering line on the "top" of the screen, you can cover this by pressing the menu when you are in the bouquetlist and select "cover dashed flickering line for this service".
Harddrives will fail, that's just a question of time, so a check from time to time is prudent,certainly when you have switched it off using the power switch or pulled the plug, as this will mess-up the filesystem. (btw it can also be a USB stick but it has to be formated ext3 or 4). When a internal drive is present you can check it using the menu. Main menu -> Setup -> System -> Expert Settings -> Harddisk -> Filesystem check.
I cannot record with my receiver or recording with a Zapper (eg. Vu Zero / Vu Solo Se)
By default some Vu+ boxes are a zapper, meaning you can not record with it. If you want to record with it, you can install the "pau" plugin/extension. It is located in the extensions section of the plugin browser.
==Missing menu items As of OpenPLi 7.0 you will be asked to select the Setup mode, here you can choose between 3 different user modes; Normal, Advanced or Expert. Each mode will reveal more options in the Menu to setup.
Here are some solutions when you run into problems with mounting\sharing a medium (HDD) in your network.
Older vs newer Kernel
When your box uses a kernel 3.x (Menu-Information-About) and you want to mount something that has a kernel 4.x your CIFS share might fail, even though you entered the data carefully, but there is a solution.
The solution is simple, you can try the following; If you make a mount with Mountmanager, change the "mount options" from "rw" to "rw, sec=ntlm", this will lower the security standard from ntlmv2 (default with kernel 4.x and up) to ntlm.
Now exit and re-mount or Reboot your box and if this was the cause, you can now access your share.
Older vs newer SMB Protocol
There is a similar issue regarding the version of the SMB protocol used.
There are several versions of the SMB protocol, v1, v2.0, v2.1 and v3. (see https://blogs.technet.microsoft.com/josebda/2013/10/02/windows-server-2012-r2-which-version-of-the-smb-protocol-smb-1-0-smb-2-0-smb-2-1-smb-3-0-or-smb-3-02-are-you-using/ for more in-depth information).
Recently, due to several security issues, an action has been ongoing to disable the unsafe SMBv1, not only in Windows, but also in NAS systems like Synology for example. Windows has the option to cycle through all available and allowed protocols when you want to connect to a share, so you as a user don't notice anything and don't know which protocol is used. But the Linux kernel driver doesn't. It connects using the version it has been programmed with, and if you as a user need a different version, you need to specify this in the mount options.
Up to kernel v4.13 (at the moment of writing all supported receivers), the default was SMBv1, after that, the default has been upgraded to SMBv3. So if your box has a kernel older than 4.13, and your "server" doesn't support SMBv1, you need to specify the version on the mount. Likewise, if your box runs 4.13 or higher, and your "server" doesn't support SMBv3, you also need to specify the version on the mount.
The solution is to change the SMB version used to mount, to do this in Mountmanager change the "mount options" from "rw" to "rw, vers=3.0" (or whatever version you want to mount). You might have to try a few, if you don't know which one your server supports, but always start with the highest version.
This is a good overview on this subject: https://www.happyassassin.net/2017/11/03/linux-kernel-4-13-and-smb-protocol-version-fun/
The same is true for the authentication mechanism. This used to be NTLM, but in Kernel 3.8 the default has changed to NTLMv2, as Windows no longer supports NTLM (also because of security issues). But depending on the version and configuration of Windows (especially Windows Server), you might need to specify an alternative mechanism on the commandline too.
Reset lost password
In case you have lost your box password or someone else has been so 'funny' to create a password without having informed you, there are several ways to solve this issue.
Install the "setpasswd" plugin
Easiest way is to install a plugin and reset or delete your password. Goto Main menu -> Plugin browser and press the green button "download plugins" goto systemplugins and goto setpasswd and press ok on your remote to install it. After you installed goto Main menu -> Setup -> System -> Change Root Password and press the red button to delete it.
Using the command line method 1
I assume that you still have access via Explorer with \\boxname or \\ipaddressbox. If not, then the only 'solution' to get access again is to flash your box which is actually not a solution.
- Go to the map /etc where you find the file shadow.
- If you owe another Enigma2 box then go to the map \etc and copy there that file 'shadow'.
- Go to the box with the unknown password and paste the just copied file from the other box over your present version of shadow.
Using the command line: method 2
There is a second scenario to solve this.
- Go to the map /etc where you also find the file passwd.
- Select and edit the file passwd with right mouse button and select a proper editer. I use Notepad ++
- In this file the line: root: x: 0: 0: root: / root: / bin / sh or something as root: EIfidfjeSAEFKEOlasdf5ewr3rWEW: 0: 0: root: / root: / bin / sh is the actual PW. The Password field is x or the encrypted string EIfidfjeSAEFKEOlasdf5ewr3rWEW
- Delete the x or the string The line is now following: root :: 0: 0: root: / root: / bin / sh
- Save / overwrite this file and exit Notepad ++.
Splash screen replacement
The splashscreen is written in a limited reserved space of flash. We believe that the splash screen is not intended to be image specific, it should just show the manufacturer and/or box type information. The dimensions and type of splash file supported by the bootloader, differ per brand, and possibly even per box. We advice to stay away from that, leave the splash screen to the bootloader, and the manufacturer.
If by some reason, let's say another image, has changed it, you can restore it to the one from the manufacturer. Do a search on the OpenPLi site using Google and type:
splash screen site:openpli.org
For the Edision jump to Restore Splash screen for Edision
For the Vu+ jump to Restore Splash screen for Vu
For the Zgemma jump to Restore Splash screen for Zgemma
Time, if you have problems getting the correct time
There are 2 solutions, if somehow you don't have the right time on you receiver, using the internet or use the transponder of a satellite.
Here you install a plugin called Systemtime, it is in Main menu > Pluginbrowser > Download plugins > Systemplugins and uses NTP, just like your desktop PC, to get the time from an internet time server, so after installing it, it will be in Main menu > Setup > Sytem and there are various settings.
OpenPLi will, at startup retrieve the time from a transponder, so if you have a satellite setup, it is wise to make use of the Startup service. By doing so and choosing a reliable transponder (=channel) you will always have the right time. For the Dutch, choosing an NPO channel will be a good choice.
USB memory sticks working or not
When you want to use an USB memory stick, lets say for flashing your box with OpenPLi, there is no way of telling your stick might work, it's trial and error! Because the USB detection system in the bootloader of your receiver is very simple, there are 2 things to consider:
- It has a short device detection time, which is as it should be, because a long device detection time could result in an annoying long booting procedure. This (short device detection) causes devices whose detection takes (too) long (usb3 devices, large sticks) not to be seen in time.
- It takes the first device that is found and if you've connected multiple devices, chances are that it's not the device you want to use.
Generally speaking, small old USB sticks with less than 1Gb have a bigger change to work.
Video codecs and what if you can not play a movie on your receiver
Video Codecs are not needed for your receiver. The difference between your PC/Lab top and your Receiver is that your PC/Lab top uses its processor to decode the video, while your receiver uses a specialized chip. For your PC/Lap top you can therefore add new codecs by installing software, with your receiver the codecs consist of electronic circuits in the chip and therefore codecs can't be added, so only the "codecs" in the chip can be played.
So if you have a movie that can't be played, you'll have to re-code it. For this you can use programs like Handbrake. A good choice would be h264 or h265 as a video codec and mp2, mp3 or ac3 as an audio codec.